• Digital Video Input: HDMI, DVI-D*, Dual-Mode DisplayPort (DP++)*
• Analog Video Input: HD-15 VGA, Component*
• Video Output: Video Output
• Formats: HDMI, DVI-D*, Dual-Mode DisplayPort (DP++)*, HDCP content protection support, RGBHV, YPbPr
• Progressive Input Resolutions
• Supports most common HD up to 1920×1200.
• Interlaced Input Resolutions
• Supports 1080i60.
• Analog Input Resolutions
  NOTE: Input resolutions supported @60Hz refresh rates are also supported @59.94Hz.
• Supports most common HD up to 1920×1200.
• Output Resolutions: Matched to inputs.
• Analog-To-Digital Conversion: 8-bit 165 MHz per each of three color channels
  NOTE: The N1115-WP does not accept Composite or S-Video (YC).
• Color Space: 4:2:2

*These signal types are supported through a passive adapter.

• Input Signal Types: Embedded audio on HDMI (DVI-D through adapter) or Analog Stereo
• Output Signal Types: Ethernet
• Analog Audio Format: 8ch PCM, Stereo 2-channel
• Analog-To-Digital Conversion: 16-bit 32 kHz, 44.1 kHz and 48 kHz

• Latency: 10 ms at 60 fps
• Bandwidth: 840 Mb/s (varies with resolution)

Note: This is the combined encode plus decode latency. Total latency from source to screen will also include any network latency.

Note: Scaling adds one frame of latency (17ms at 60fps).

• Ethernet: 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
• HDMI: HDCP, EDID management

• P0:
• 8-wire RJ45 female
• 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
• Provides the network connection, network AV video, and power to the Encoders and Decoders
• HDMI IN: HDMI video input
• VGA IN: DB15 analog input
• USB IN – Host: USB-B host input
• USB IN – Maintenance: USB-Mini maintenance input

• RESET Button:
• Recessed pushbutton
• Press to initiate a ‘warm restart’ causing the processor to reset, but not lose power. A reset does NOT affect the current settings
• POWER LED: On solid (green) when operating power is supplied (via PoE or local power supply)
• AUDIO LED: On (green) when audio is transmitting.
• ANALOG VIDEO LEDs: On (green) when analog source is available and transmitting.
• DIGITAL VIDEO LED: On (green) when video source is available and transmitting
• HDCP LED: On (green) when the source is using HDCP
• STREAM LED: On (green) when the unit is streaming video
• STATUS LED: Flashing (green) when the unit is active.
• LINK/ACT LED: Flashing (yellow) when network traffic is being sent or received.

• Power over Ethernet
• Can be powered via a PoE switch or other equipment with a PoE source. Conforms to IEEE 802.3af Class 3 (802.3at Type 1)
• Point-to-point applications between the encoder and a decoder requires a PoE injector to power the wallplate encoder.

Note: In order for the unit to receive Power over Ethernet (PoE), it must be connected to a switch or other equipment that has a PoE PSE (Power Sourcing Equipment) port. Warning: Do not run wiring that is connected to a PoE PSE port outside of the building where the PSE resides. It is for intra-building use only.

• Temperature (Operating): 32° to 104°F (0° to 40°C)
• Temperature (Storage): -22° to 158°F (-30° to 70°C)
• Humidity (Operating): 10% to 90% RH (non-condensing)
• Humidity (Storage): 0% to 90% RH (non-condensing)
• Heat Dissipation: Up to ~26 BTU/hr

• Dimensions (HWD): 4.06″ x 3.5″ x 2.25″ (10.31 cm x 8.84 cm x 5.72 cm)
• Weight: .75 lb (0.34 kg)
• Airflow: Natural convection via vent openings on front, back, and top
• Installation
• Mounts onto standard 2 gang US back boxes
• Mounts into standard décor style wallplates (not included)
• Regulatory Compliance: FCC, CE, and NTRL
• Recommended Accessories
• Compatible with NMX-ENC-N1222, NMX-ENC-N1233, NMX-ENC-N1512, and NMX-NVR-N6123
• PS-POE-AT-TC High-Power PoE Injector, 802.3AT Compliant FG423-84)

FGN1115-WP-WH (White)
FGN1115-WP-BL (Black)