• Digital Video Input: HDMI, DVI-I (through adapter)
• Analog Video Input
• HD-15 VGA, Component
• Component is supported through a passive adapter
• Video Output: Network video over Ethernet via RJ45 port
• Formats
• HDMI, DVI-D (through adapter), Dual-Mode DisplayPort (DP++), HDCP content protection support, RGBHV, YPbPr
• DVI-D and Dual-Mode DisplayPort (DP++) are supported through a passive adapter
• Progressive Input Resolutions
• Supports most common HD resolutions up to 1920×1200.
• **720×480@59Hz, 640×480@60Hz, **720×480@60Hz, **720×576@50Hz, 800×600@56Hz, 800×600@60Hz, **1280×720@50Hz, **1280×720@59Hz, **1280×720@60Hz, 1360×768@60Hz, 1366×768@60Hz, 1024×768@60Hz, 1280×800@60Hz, 1152×864@60Hz, 1600×900@60Hz, 1440×900@60Hz, 1280×960@60Hz, 1280×1024@60Hz, ***1600×1200@60Hz, 1680×1050@60Hz, 1920×1080@23Hz, 1920×1080@24Hz, 1920×1080@25Hz, 1920×1080@29Hz, 1920×1080@30Hz, **1920×1080@50Hz, **1920×1080@59Hz, **1920×1080@60Hz, **1920x1080i@50Hz, **1920x1080i@59Hz, **1920x1080i@60Hz, ***1920×1200 @ 60Hz
• Interlaced Input Resolutions
• Supports 1080i60.
• Analog Input Resolutions
  NOTE: Input resolutions supported @60Hz refresh rates are also supported @59.94Hz.
• Supports most common HD resolutions up to 1920×1200.
• **720×480@59Hz, 640×480@60Hz, **720×480@60Hz, **720×576@50Hz, 800×600@56Hz, 800×600@60Hz, **1280×720@50Hz, **1280×720@59Hz, **1280×720@60Hz, 1360×768@60Hz, 1366×768@60Hz, 1024×768@60Hz, 1280×800@60Hz, 1152×864@60Hz, 1600×900@60Hz, 1440×900@60Hz, 1280×960@60Hz, 1280×1024@60Hz, ***1600×1200@60Hz, 1680×1050@60Hz, 1920×1080@23Hz, 1920×1080@24Hz, 1920×1080@25Hz, 1920×1080@29Hz, 1920×1080@30Hz, **1920×1080@50Hz, **1920×1080@59Hz, **1920×1080@60Hz, **1920x1080i@50Hz, **1920x1080i@59Hz, **1920x1080i@60Hz, ***1920×1200 @ 60Hz
• Analog-To-Digital Conversion: 8-bit 165 MHz per each of three color channels
  NOTE: The N2122 Encoder does not accept Composite or S-Video (YC).

**supported in component mode

***reduced blanking only

• Input Signal Types: Embedded audio on HDMI (DVI-D through adapter) or Analog Stereo (Balanced or Unbalanced)
• Output Signal Types: Ethernet at 48-kHz (standard SVSI audio stream or AES67, user selectable)
• HDMI Audio Formats: 8ch PCM
• Analog Audio Formats: Stereo 2-channel
• Analog-To-Digital Conversion: 16-bit 32 kHz, 44.1 kHz and 48 kHz

• Video 50 ms for 720p60
• Video 140ms for 1080p60
• Audio Latency: standard SVSI audio stream = 17 ms (synced to video); AES67 = <1 ms adjustable to 17 ms

Note: This is the combined encode plus decode latency. Total Latency from source to screen will also include any network latency.

Note: Scaling adds one frame of latency (17ms at 60fps)

• Ethernet: 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP.
• HDMI: HDCP, EDID management

• +12V 2A: One 12 Volt DC power input.
• P0
• 8-wire RJ45 female
• 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
• Provides network connection, network AV video, and power to the Encoders and Decoders
• P1
• 8-wire RJ45 female
• 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
• Provides network connection
• IR: 2-pin terminal Phoenix connector. Provides Infrared (IR) output only (33-60 kHz; typically 39 kHz). Emitter may be necessary (not included)
• RS232: 3-pin terminal Phoenix connector which provides a serial control interface. Full duplex communication. Available terminal speed settings: 1200-115200 baud rate
• AUDIO: 5-pin terminal Phoenix connector which provides user-selectable balanced/unbalanced input. Dedicated audio input
• HDMI OUT: HDMI video output
• HDMI IN: HDMI video input
• VGA IN: DB15 analog input

• RESET Button
• Recessed pushbutton
• Press to initiate a ‘warm restart’ causing the processor to reset, but not lose power. A reset does NOT affect the current settings
• ID Button
• Recessed pushbutton
• Press to send a notification out on the network to identify the unit (the notification causes a pop-up dialog in N-Able and N-Command)
• POWER LED
• On solid (green) when operating power is supplied (via PoE or local power supply)
• This activity is also shown by the PWR LED on the rear panel
• STATUS LED
• On flashing (green) when there is software activity
• This activity is also shown by the STAT LED on the rear panel

• PWR LED: Same as POWER LED described above
• HDMI LED: On (green) when there is a connection to a valid video source
• STAT LED: Same as STATUS LED described above
• STRM LED: On (green) when the unit is streaming video

• Temperature: 32° to 104°F (0° to 40°C)
• Humidity: 10% to 90% RH (non-condensing)
• Heat Dissipation: Up to ~44 BTU/Hr

• Regulatory Compliance: FCC, CE, and NTRL
• Recommended Accessories: NMX-ACC-N9206 (FGN9206), 2RU Rack Mount Cage with Power for Six SVSI N-Series Card Units